Twelve Or Twenty-Four Port T1/E1/J1 cPCI Module Based on the
MPC8260 Series PowerQUICC II™ Series
Features
- MPC8280 Up To 450MHz with Integrated PCI
- Twelve Front Panel RJ45 T1/E1/J1 Software Configured Interfaces
- Twelve Backplane RJ45 T1/E1/J1 Software Configured Interfaces
- CSU/DSU Support
- 32-512MB SDRAM with ECC
- 16-128MB Soldered and 512KB Socketed Flash
- Optional ATM over T1/E1 and IMA support
- Optional RS-232 SMC Port
- PICMG 2.16 Back Panel 10/100Mbps Ethernet
- H.110 Bus Interface
- VxWorks BSP
- Linux LSP
Typical Applications
- Frame Relay
- ISDN D-channel Signalling
- LAN/WAN Data Transport Wireless Basestations
- Signaling System 7 (SS7)
Description
The XPort2020 is an intelligent communications controller targeting
high performance yet low cost communications applications.
XPort2020 realizes the full potential of the MPC82xx (PowerQUICC II™)
series by supporting up to three MPC8280 eight port
solutions including ATM over T1/E1 and Inverse Multiplexing over
ATM (IMA) support.
The XPort2020 supports fully channelized HDLC and transparent protocols over 24 software configured T1/E1/J1 interfaces, with CSU/DSU support and optionally Signaling System 7 (SS7). Twelve of the T1/E1/J1 interfaces can be brought through the front panel, and the other twelve T1/E1/J1 interfaces can be brought through the backplane I/O. An integrated H.110 controller adds a flexible I/O routing structure to all 24 TDM interfaces. The XPort2020 is also capable of supporting the PICMG 2.16 protocol for interfacing two ethernet (10/100Mbps) ports through the backplane.
Hot Swap support allows XPort2020 to be installed into a live system without disrupting CompactPCI bus activity.
Processor
- MPC8280
- Embedded PowerPC G2 Core
- 133-450MHz
- 280 Dhrystones at 200MHz
- up to 100MHz 60x Bus
- 16KB Instruction and Data Caches
- 32KB internal SRAM
- Integrated MMU
- Core Disabled Mode supported
- 32-512MB SDRAM
- 16-128MB Surface Mount and 512KB Socketed Flash
Front Panel Connections
- Up to Twelve T1/E1/J1 line interfaces.
Backplane Connections
- Up to Twelve T1/E1/J1 line interfaces
PICMG 2.1
- Hot Swap Support Allows Insertion and removal from an active CompactPCI bus
PICMG 2.3
- Routes PTMC I/O to J3
PICMG 2.5 H.110 Support
- Intel T8110 H.110 BusController
- Allows timeslots to be routed between the host and all 24 T1/E1/J1 Ports.
PICMG 2.9
- Dedicated IPMI Microcontroller
- Ability to control power and reset to the PMC slots
- Monitors 1.5V, 1.8V, 2.5V, 3.3V, 5V, +12V, -12V
- Monitors Board Temperature
PICMG 2.16
- Two 10/100Mbs ethernet interfaces
Multi Communication Controller
- HDLC and Transparent modes
- 256 total channels
- Independent Tx/Rx clocking per TDM
PM4351 Comet Framer
- T1/E1/J1 Interface Standards
- Long and Short Haul LBO’s
- 1.544MHz and 2.048MHz rates
- Software configured interface modes
- CSU/DSU
Software
- MCC, CSU, SMC, ATM, IMA, SS7 and Ethernet Drivers
- VxWorks BSP
- Linux LSP
Physical
- 6U CompactPCI Form Factor
- 233.35mm x 160mm
Power Requirements
- +3.3V 3.75A 12.39W
- +5.0V 0.0077A 0.039W
- +12.0V 0.00A 0.0W
- -12.0V 0.00A 0.0W
Operating Temperature
- 0 to +55C ambient, at board
Humidity
- 0% to 85%
Storage Temperature
- -40 to +70C
Copyright © 2005, X-ES
Extreme Engineering Solutions, Inc.
3225 Deming Way, Suite 120
Middleton, WI 53562
Extreme Engineering Solutions, Inc.
3225 Deming Way, Suite 120
Middleton, WI 53562
Phone: 608-833-1155
Fax: 608-827-6171
Web: http://xes-inc.com
Email: sales@xes-inc.com
Fax: 608-827-6171
Web: http://xes-inc.com
Email: sales@xes-inc.com
