XCalibur1502

NXP (formerly Freescale) MPC8572E Processor-Based Conduction- or Air-Cooled 6U cPCI Module

With dual PowerPC e500 cores running at up to 1.5 GHz, the MPC8572E delivers enhanced performance and efficiency for today's embedded computing applications.

End of Life

Please contact X-ES Sales for assistance with choosing a recommended replacement product.

Learn more about this product below »
REQUEST A QUOTE ASK A QUESTION

Contact us directly at +1 (608) 833-1155

SKU: 90050285 Category:
XCalibur1502 6U cPCI SBC

The XCalibur1502 is a high-performance, multiprocessing, 6U CompactPCI, single board computer that is ideal for ruggedized systems requiring high bandwidth processing and low power consumption. With dual Power Architecture® e500 cores running at up to 1.5 GHz, the NXP (formerly Freescale) MPC8572E delivers enhanced performance and efficiency for today’s embedded computing applications.

The XCalibur1502 provides two separate channels of up to 4 GB (2 GB each) DDR2-800 ECC SDRAM, two XMC/PrPMC slots, as well as 256 MB of NOR flash (with redundancy). The XCalibur1502 also supports four Gigabit Ethernet ports, I²C, XMC I/O, PMC I/O, and RS-232/422/485 serial ports out the front panel or J5 connector.

The XCalibur1502 is a powerful, feature-rich solution for the next generation of compute-intensive embedded applications. Operating system support for Wind River VxWorks, Green Hills INTEGRITY, QNX Neutrino, and Linux is available.

Features

  • NXP PowerQUICC™ III MPC8572E processor with dual Power Architecture® e500 cores at up to 1.5 GHz
  • Air cooling
  • Up to 4 GB DDR2-800 ECC SDRAM in two channels
  • Up to 4 GB of NAND flash
  • Up to 256 MB of NOR flash (with redundancy)
  • Four Gigabit Ethernet ports
  • x8 PCI Express to XMC sites
  • Two RS-232/422/485 serial ports
  • Two XMC/PrPMC interfaces
  • Linux BSP
  • Wind River VxWorks BSP
  • Green Hills INTEGRITY BSP
  • QNX Neutrino BSP (contact factory)

Technical Specs

Processing Nodes

  • NXP (formerly Freescale) PowerQUICC™ III MPC8572E processor
  • Dual Power Architecture® e500 cores at up to 1.5 GHz
  • 1 MB of shared L2 cache

Memory

  • Up to 4 GB (2 GB each) of DDR2 ECC SDRAM in two channels
  • Up to 4 GB of NAND flash
  • Up to 256 MB of NOR flash (with redundancy)
  • 16 kB I²C SEEPROM
  • Optional Trusted Platform Module (TPM)

cPCI

  • 66 MHz 64-bit PCI interface to J1 and J2
  • PICMG 2.1 (Hot Swap support)
  • PICMG 2.3 (PMC I/O to J3 and J5)
  • PICMG 2.9 (dedicated IPMI controller)
  • PICMG 2.16 (two 10/100/1000BASE-T Ethernet ports)

Front Panel

  • Two RS-232/422/485 serial ports
  • One or two Gigabit Ethernet ports
  • General purpose LEDs

Back Panel

  • Two RS-232/422/485 serial ports
  • Two Gigabit Ethernet ports
  • PMC I/O

Software Support

  • Linux BSP
  • Wind River VxWorks BSP
  • Greens Hills INTEGRITY BSP
  • QNX Neutrino BSP (contact factory)

Environmental Requirements

Contact factory for appropriate board configuration based on environmental requirements.

  • Supported ruggedization levels (see the X-ES Ruggedization Chart): 1
  • Conformal coating available as an ordering option

Power Requirements

  • Power will vary based on configuration and usage. Please consult factory.

Accessories

Please contact X-ES Sales at sales@xes-inc.com or by phone at +1-608-833-1155 for information on this product's accessories.

Documentation

Datasheet

To view all of the information about this product in a PDF, please download the datasheet.

Download Datasheet

Technical Documents

SupportNet is your source for product manuals, technical support, and software downloads.

Access SupportNet

Block Diagram

Additional Information

Datasheet

View the XCalibur1502
Datasheet PDF

Download Datasheet

6U cPCI SBCs

View the full selection of 6U cPCI SBCs from X-ES

View All
Back to Top
Fast, Flexible, and Customer-Focused Embedded Solutions
© 2018 Extreme Engineering Solutions, Inc