XChange1004

Dual PrPMC cPCI Carrier Card with PICMG 2.16 Switched Ethernet

The XChange1004 is a 6U CompactPCI dual PMC carrier card with a PICMG 2.16 Gigabit Ethernet interface. The XChange1004 detects if it is a system controller and configures the cPCI bridge to operate in transparent mode. As a peripheral, the cPCI bridge operates in non-transparent mode, which offers address isolation, in addition to electrical isolation.

End of Life

Please contact X-ES Sales for assistance with choosing a recommended replacement product.

Learn more about this product below »
REQUEST A QUOTE ASK A QUESTION

Contact us directly at +1 (608) 833-1155

SKU: 90050100 Category:
XChange1004 cPCI Carrier Card

The XChange1004 is a 6U CompactPCI dual PMC carrier card with a PICMG 2.16 Gigabit Ethernet interface. The XChange1004 detects if it is a system controller and configures the cPCI bridge to operate in transparent mode. (A PrPMC must be installed on the XChange1004 if it is used in the system slot, since there are no intelligent devices on the XChange1004.) As a peripheral, the cPCI bridge operates in non-transparent mode, which offers address isolation, in addition to electrical isolation.

PICMG 2.1 Hot Swap support allows the XChange1004 to be installed into a live system without disrupting CompactPCI bus activity. In addition, the system management bus support allows the card to be powered down and reset remotely through the PICMG 2.9 IPMI interface. The IPMI interface also allows for the monitoring of voltage and temperature levels on the cards attached to the two PrPMC slots.

Features

  • 100 MHz PCI-X cPCI and local bus interfaces
  • Autosense system/peripheral slot
  • Hot Swap support
  • Two backplane Gigabit Ethernet ports
  • Complies with PICMG 2.0, 2.1, 2.3, 2.9 and 2.16
  • IPMI satellite management controller
  • Wind River VxWorks BSP
  • Linux BSP

Technical Specs

cPCI

  • 66 MHz 64-bit PCI interface to J1 and J2
  • PICMG 2.1 (Hot Swap support)
  • PICMG 2.3 (PMC I/O to J3 and J5)
  • PICMG 2.9 (dedicated IPMI controller)
  • PICMG 2.16 (two 10/100/1000BASE-T Ethernet ports)

PCI-X PMC Slots

  • Maximum aggregate bandwidth of 1 Gb/s
  • Processor PMC (PrPMC) support
  • 10 mm stacking height

Software Support

  • Linux BSP
  • Wind River VxWorks BSP
  • Ethernet and IPMI drivers

Physical Characteristics

  • 6U cPCI form factor
  • 233.35 mm x 160 mm

Environmental Requirements

Contact factory for appropriate board configuration based on environmental requirements.

  • Supported ruggedization levels (see the X-ES Ruggedization Chart): 1
  • Conformal coating available as an ordering option

Power Requirements

  • 3.3 V, 0.61 A, 2 W

Accessories

Please contact X-ES Sales at sales@xes-inc.com or by phone at +1-608-833-1155 for information on this product's accessories.

Documentation

Datasheet

To view all of the information about this product in a PDF, please download the datasheet.

Download Datasheet

Technical Documents

SupportNet is your source for product manuals, technical support, and software downloads.

Access SupportNet

Block Diagram

Additional Information

Datasheet

View the XChange1004
Datasheet PDF

Download Datasheet
Back to Top
Fast, Flexible, and Customer-Focused Embedded Solutions
© 2018 Extreme Engineering Solutions, Inc